Ipamorelin Dosage Calculator
Ipamorelin is a selective growth-hormone secretagogue supplied lyophilized, often in 5 mg or 10 mg vials and frequently as a blend with CJC-1295. Enter the vial strength and diluent volume to see the exact syringe reading.
- Concentration
- 2500 mcg / mL
- Concentration
- 2.50 mg / mL
- Per syringe unit
- 25.0 mcg / unit
- Draws per vial
- 25.0
- Total solution
- 200 units
Every figure below is arithmetic performed in your browser. Nothing here is a protocol, recommendation, or medical guidance — all Ares Research materials are supplied for in-vitro laboratory research only.
HPLC purity and mass-spec identity confirmation, published per batch. US-based tracked shipping.
Calculating a blend vial correctly
Blend vials list two masses — for example 5 mg CJC-1295 + 5 mg Ipamorelin. The diluent volume applies to the vial as a whole, so each component has its own concentration. Run the calculator once per component using that component's mass: 5 mg in 2 mL gives 2,500 mcg/mL of that component, and one syringe draw delivers both components in the ratio the vial was blended at.
Microgram-scale readings
Ipamorelin research amounts are typically in the low hundreds of micrograms. A 5 mg vial in 2 mL gives 2,500 mcg/mL, so 200 mcg is 0.08 mL — 8 units, a tight reading. Reconstituting in 5 mL gives 1,000 mcg/mL and moves the same 200 mcg to 20 units, a meaningfully more accurate mark.
Handling notes
Introduce diluent down the vial wall, swirl gently, and refrigerate once dissolved. Do not shake. Keep blend vials clearly labelled with both component masses and the diluent volume used, since a blend's syringe reading cannot be reconstructed from the vial label alone.
Frequently asked questions
How many units is 200 mcg of Ipamorelin?
+
With a 5 mg vial reconstituted in 2 mL, the concentration is 2,500 mcg/mL, so 200 mcg is 0.08 mL — 8 units on a U-100 insulin syringe. In 5 mL of diluent the same amount is 20 units, which is easier to measure accurately.
How do I calculate a CJC-1295 and Ipamorelin blend vial?
+
Treat each component separately. A 5 mg + 5 mg blend in 2 mL gives 2,500 mcg/mL of each component, so a 0.08 mL draw delivers 200 mcg of both simultaneously. Enter one component's mass at a time in the calculator; the draw volume is shared.
How much bacteriostatic water for a 5 mg Ipamorelin vial?
+
3 mL to 5 mL is often preferred for microgram-scale work because it pushes the reading further along the U-100 barrel. 2 mL is also common and yields 2,500 mcg/mL, but small draws land in single-digit unit readings.
How should reconstituted material be stored?
+
Once reconstituted, most research peptides are held refrigerated at roughly 2–8°C, protected from light, in the original sealed vial. Bacteriostatic water contains 0.9% benzyl alcohol, which suppresses microbial growth in the diluent. Temperature, light exposure, and repeated freeze-thaw cycles all affect stability, so consult the compound-specific certificate of analysis and published stability data.
How do I read a U-100 insulin syringe?
+
A U-100 barrel is graduated in units where 100 units equal 1 mL, so each single-unit mark is 0.01 mL. To convert a volume in mL to units, multiply by 100 — 0.25 mL is 25 units. This calculator reports both figures so you can cross-check the mark against the volume.
Related calculators
Tesamorelin vials → concentration, syringe units, and draws per vial.
Any vial, any diluent volume, any target amount → concentration, syringe units, doses per vial.
Compare diluent volumes before you mix — see how each one changes the syringe reading.